Vanasche Motorsports 2019 KTM 690 fuel filler neck CNC (Black or Orange)
Only a few left!
Fits
KTM690 enduro and SM KTM690 2019-2024
Aluminium fuel tank neck comes in orange or black suit KTM690 2019-2021
- looks great
- no more problems with trying to unlock cap when mud and sand gets in to lock
- fits up with fuel sock to save you fuel pump
NOTE: when used with 2021 you will need to reposition seat release cable back to the original position from 2019 on LH side all parts are same so not difficult. or you can extend cable to rear of rear mudguard. You can give us a call to explain if you want
Vanasche Motorsports Rear disc guard Husqvarna/KTM 701/690
MADE IN USA
Machined from 1.25" aluminium plate this rear disc guard has been designed to take all the abuse you can throw at it. Guaranteed to give maximum protection in the harshest environments. suits all model 690R and 701
Colours: orange, blue, polished and black.
Vanasche Motorsports Side Stand Foot suits- KTM & Husqvarna Adventure bikes
Only a few left!
Side stand foot :
A two-piece part that combines a machined piece of billet aluminium base with a laser cut plate on top, powder coated black. This give you more surface area to better support your bike.
suits KTM 690,790,1090,1190 &1290 Husqvarna 701
Vanasche Motorsports Stand Bypass Dongle 701 Husqvarna & KTM690,1090,1190,1290
Only a few left!
2021 Dongle has change on EU models new dongle to suit NOW IN STOCK
The standard stand switch installed by KTM/Husqvarna is a safety device designed to ensure stand is up before you ride away. The switches fail and leave riders stranded in far from home. This dongle is designed to bypass the failed switch, by simply plugging it into the stand switch plug. This dongle can be carried as it is only slightly larger than a 20 cent piece. Easy install is stand switch fails just plug it in, and make sure the stand is up.
Disclaimer
It is the owners responsibility to ensure that the stand is in the up position before riding away when the dongle is in use. This component is not designed to be permanently installed as it bypasses a safety device.
Vanasche Motorsports Case Saver to suit 701/690 - Black, Blue or Orange
Case Saver to suit Husqvarna 701, Enduro & SM
- CNC machined from billet aircraft grade aluminium this case saver was built to protect your fragile engine case and clutch slave cylinder. Each case saver comes with OEM style hardware and chain slider.
- Maximum Front Sprocket Size: 16 Teeth
NEW! Vanasche Motorsports Stainless Steel Adventure Foot Pegs
Sold out
Over-sized and Lowered Rally Foot pegs fabricated from laser cut and machined components using high grade stainless steel. These TIG welded foot pegs feature a skeletal design to help shed mud/debris and boast platforms that are 11mm wider and 13mm longer than the factory foot pegs for improved comfort and control. The pegs are 1.0" (25mm) lower than factory. The outer 3 teeth around the curvature are 2mm higher than the rest to reduce side slip.
Fitment (Please Choose Appropriate Bike In Upper Right):
- KTM 690 - All Years
- Husqvarna 701 - All Years
- KTM 640/790/890/950/950SE/990/1090/1190/1290 - All Years
- Husqvarna 901 - All Years
Features:
- 1" Lower than Factory
- Heavy Duty Machined Clevis for added strength and perfect fitment
- The tread area is oversized: 2-3/8" Width x 3-3/4" Length
- Skeletal design for shedding of mud/debris
- Full oval internal stiffener and low profile underside gussets to maintain ground clearance and exceptional strength
- High Grade Stainless Steel Material
- Taller outer teeth to reduce side slip (taller by 2mm)
- Includes new pair of cotter pins (factory springs are reused)
Vanasche Motorsports Adventure Foot Pegs
Only a few left!
Vanasche CNC Adventure Foot pegs Made In USA
Oversized Billet Foot pegs machined from 7075 High Strength Aerospace Grade Aluminium paired with your choice of tread plate. Comfort & Control were the primary focus points in creating this product.
Fitment:
- KTM 790/890/1090/1190/1290 - All Years
- Husqvarna 901 Norden - All Years
Features:
- 3/4" Lower than Factory
- 1/4" Rearward Position
- The tread area is oversized: 2-3/8" Width x 3-7/8" Length
- 7075 Aluminium Alloy is Double the strength of 6061
- Includes new pair of cotter pins & springs
.
The set screws offer superior traction and gives you the ability to change out lengths and effectively alter the angle of the surface. The setscrew plates offer the highest level of grip/traction. Each set of setscrew pegs comes with an entire set of 10mm and 12mm long screws as well as new cotter pins and an allen wrench.
Vanasche Motorsports oversized Billet Foot pegs are machined from 7075 High Strength Aircraft Grade Aluminium paired with your choice of tread plate.
Fitment:
- KTM EXC pre 2016
- KTM690 all models
- KTM 640/790/950/950SE/990/1090/1190/1290 all years
- Husqvarna 701 all models
- Husqvarna 901 Norden
Features:
- 20mm Lower than Factory
- 8mm Rearward Position
- The tread area is oversized: 60.3 mm Width x 98.5mm Length
- 7075 Aluminium Alloy is Double the strength of 6061
- Includes new pair of cotter pins & springs
The set screws offer superior traction and gives you the ability to change out lengths and effectively alter the angle of the surface. The set screw plates offer the highest level of grip/traction. Each set of setscrew pegs comes with an entire set of 10mm and 12mm long screws as well as new cotter pins.
Vanasche Motorsports Bar Risers or steering damper mounts KTM690 2019+
Only a few left!
Say goodbye to twisted bars! A rock solid solution for the KTM690 2019+
You have a choice of
- Bar Risers only
- Bar Risers with damper mounting plate
- Bar Risers damper mounting plate frame mount and pin
- Bar Risers damper mounting plate frame mount, pin and Scott Damper
Description
- Relaxed Ergonomics from increased bar height (15mm or 30mm)
- Immediate confidence boost with more race inspired control/feeling
- Two bar offsets (fwd/rwd) are achievable by flipping risers 180*
- Narrow submount allows clearance for fork tubes allowing you to slide the forks up if front end lowering is desired
- Solid Aluminum Cone Inserts
- 12mm Alloy Bolts
- Billet Machined Submount, Risers, Top Clamp all anodized in black colour
- Scott's Tower & Pin
- Works with Scott's Steering Stabilizer
- Works with 1-1/8" diameter bars only
The factory bar setup with rubber cones, 10mm bolts, and thin aluminium components leaves much to be desired.
We replace the factory rubber cones with aluminium inserts in favour of a rigid bar setup and replace the mounting bolts with larger 12mm alloy socket head cap screws. The subplate, risers, and top clamp are machined from billet aluminium and anodized black.
Select from the two bar rise amounts listed (+15mm or +30mm). The riser blocks are reversible allowing for a forward/rearward offset.