Vanasche Motorsports Side Stand Foot suits- KTM & Husqvarna Adventure bikes
Only a few left!
Side stand foot :
A two-piece part that combines a machined piece of billet aluminium base with a laser cut plate on top, powder coated black. This give you more surface area to better support your bike.
suits KTM 690,790,1090,1190 &1290 Husqvarna 701
NEW! Vanasche Motorsports Stainless Steel Adventure Foot Pegs
Only a few left!
Over-sized and Lowered Rally Foot pegs fabricated from laser cut and machined components using high grade stainless steel. These TIG welded foot pegs feature a skeletal design to help shed mud/debris and boast platforms that are 11mm wider and 13mm longer than the factory foot pegs for improved comfort and control. The pegs are 1.0" (25mm) lower than factory. The outer 3 teeth around the curvature are 2mm higher than the rest to reduce side slip.
Fitment (Please Choose Appropriate Bike In Upper Right):
- KTM 690 - All Years
- Husqvarna 701 - All Years
- KTM 790/890/1090/1190/1290 - All Years
- Husqvarna 901 - All Years
Features:
- 1" Lower than Factory
- Heavy Duty Machined Clevis for added strength and perfect fitment
- The tread area is oversized: 2-3/8" Width x 3-3/4" Length
- Skeletal design for shedding of mud/debris
- Full oval internal stiffener and low profile underside gussets to maintain ground clearance and exceptional strength
- High Grade Stainless Steel Material
- Taller outer teeth to reduce side slip (taller by 2mm)
- Includes new pair of cotter pins (factory springs are reused)
Vanasche Motorsports Case Saver to suit KTM 790/890/Norden 901 - Black,Blue or Orange
Only a few left!
Case Saver to suit
- KTM 790/890 Adventure S & R models (Fits all years)
- KTM790 Duke (Fits all years)
- CNC machined from a solid piece of billet aircraft grade aluminum this case saver was built to protect your fragile engine case and stator cover. In addition to the protection it also provides a window to view your front sprocket condition and access to clean/remove debris unlike the stock cover. Each case saver comes with a proper KTM chain slider that helps reduce chain clatter at low engine speeds.
- Maximum Front Sprocket Size: 16 Teeth (factory size)
- Install instructions
Vanasche Motorsports Adventure Foot Pegs
Only a few left!
New Design pivot area
Vanasche Motorsports oversized Billet Foot pegs are machined from 7075 High Strength Aircraft Grade Aluminium paired with your choice of tread plate.
Fitment:
- KTM EXC pre 2016
- KTM690 all models
- KTM 790/1090/1190/1290 all years
- Husqvarna 701 all models
- Husqvarna 901 Norden
Features:
- 20mm Lower than Factory
- 8mm Rearward Position
- The tread area is oversized: 60.3 mm Width x 98.5mm Length
- 7075 Aluminum Alloy is Double the strength of 6061
- Includes new pair of cotter pins (factory springs are reused)
The set screws offer superior traction and gives you the ability to change out lengths and effectively alter the angle of the surface. The set screw plates offer the highest level of grip/traction. Each set of setscrew pegs comes with an entire set of 10mm and 12mm long screws as well as new cotter pins.
Vanasche Motorsports Husqvarna 901 Norden GPS Mount
Only a few left!
Hands down the most rigid setup that mounts directly to the 901 factory GPS location.
Fitment:
- Husqvarna Norden 901 - All Years
Features:
- CNC machined from solid billet aluminum extrusions
- Tapered wall machining and form tapped holes
- AMPS bolt pattern (portrait and landscape orientations)
- Includes x4 stainless M4 screws
- Same viewing angle as TFT display
- Wire pass through hole at front for access to factory accessory wiring (ie charging)
Perun Moto UPPER HANDLEBAR CLAMP 38/40X90 AMPS (suits most GPS mounts)
Only a few left!
Compatibility - Fits on majority of KTM and Husqvarna bikes with 38x90 or 40x90 bolt pattern - all MY KTM 690 Enduro and SMC-R, all MY Husqvarna 701 Enduro and Supermoto (fits on BRP sub-mounts too!), GasGas ES/SM 700, KTM 790 and 890 Adventure, KTM 1x90 Adventure bikes, Husqvarna 901 Norden and many more.
Works perfectly with Garmin Montana and Zumo series..
- AMPS bolt pattern - for vast number of GPS and phone holders, horizontal and vertical installation possible and approx. 30 mm of fore-aft positioning
- Perfectly suited for 2021+ 1290 Super adventure - enough room for "glove compartment" door to be fully opened and perfect placement of the GPS/phone relative to the dashboard,
- BRP Sub mount compatible - works with BRP Sub mount for KTM 690 Enduro and SMC-R, Husqvarna 701 Enduro and Supermoto,
- Billet part - milled out of aircraft grade aluminium-magnesium alloy,
- Durable - M4 threads for AMPS mounts are formed (not cut),
- Handlebar safe - powder coated, not anodized, which provides smooth contact with handlebar, without scuffs (top of the line IGP Duraface powders used),
- All necessary hardware provided - high quality M8 allen head zinc coated bolts and stainless M4 button head bolts.
Perun Moto DIRECT HANDLEBAR CLAMP (28.6 MM) AMPS (suits most GPS mounts)
Compatibility - fits all bikes with oversized handlebars (1-1/8" or 28.6 mm) and with split handlebar clamps.
Fits on 2021+ KTM 1290 Super Adventure, 2013-2020 KTM 1050, 1090, 1290 Adventure bikes (with stock handlebar clamps).
Works perfectly with Garmin Montana and Zumo series or QuadLock phone mount.
---
- AMPS bolt pattern - for vast number of GPS and phone holders, horizontal and vertical installation possible,
- Low profile and adjustable- easy rotation adjustment (through one easily accessible front bolt) and 60 mm of forward - aft adjustment of the upper plate,
- Billet part - milled out of aircraft grade aluminum alloy,
- Durable - formed (not cut) threads,
- Handlebar safe - powder coated, not anodized, which provides smooth contact with handlebar, without scuffs (top of the line IGP Duraface powders used),
- All necessary hardware provided - high quality M6 zinc coated bolts and stainless steel M5 and M4 bolts.
SCOTTS Stabilizer Plus 8mm Stepped Link Arm
The Scotts Plus 8mm Longer stepped link arm is designed for special applications where additional clearance of instruments, fuel tank or controls is required. The front of the slot is in the same location as the standard 40mm link arm but the slot is extended and additional 8mm to accommodate applications where the post is set further back to clear controls.
NOTE: Please use Scotts Link Arm Puller to remove Link Arm from stabilizer and to avoid costly damage to stabilizer.
Scotts stabilizer link arms are manufactured from high quality stainless steel to exacting specifications.
BRP is an authorized Scotts Stabilizer Dealer and Service centre with an extensive knowledge of stabilizer mounting applications. We have a complete line of stabilizer mounting applications and replacement parts. When it comes to service we offer complete service on all Scotts stabilizers.
SCOTTS Stabilizer Special Stepped 35mm open Link Arm
The Scotts special stepped -5mm link arm must be used with SUB Mounted applications where the front of the slot is milled further forward and the end is milled off to allow for additional clearance of tank or key assembly.
Scotts stabilizer link arms are manufactured from high quality stainless steel to exacting specifications.
BRP is an authorized Scotts Stabilizer Dealer and Service center with an extensive knowledge of stabilizer mounting applications. We have a complete line of stabilizer mounting applications and replacement parts. When it comes to service we offer complete service on all Scotts stabilizers.
Vanasche Motorsports Side Stand Bypass Dongle Husqvarna 901 Norden
The Side stand switch is a safety device, you should assess if it is safe to use this bypass dongle in your situation.
With the new era of over-complicated side stand sensors it is easy to be left stranded by a non-functioning safety device. Our product solves that inconvenience.
Fitment:
- Husqvarna Norden - All Years
Plug & Play Solution: Unplug the factory side stand sensor, plug in dongle.
NOTE: The connection for this device is directly above the engine head. You must remove the fuel tank to access and install this dongle.
Vanasche Motorsports CNC brake pedal with or without pedal pad suits Husqvarna 901 Norden
Heavy Duty Billet aluminum brake pedal machined for an exact fit for both the Husky Norden 901 Adventure models.
- Pedal includes sealed deep groove ball bearings pressed in place. A significantly larger cross-section over the factory unit improves both strength from impacts as well as rigidity to remove the flex felt in the factory pedal.
- The tapped hole through the lever cross section used for the pedal stop bolt is a notorious weak point. We've added a significant material increase in this particular area for a pedal that won't let you down. We guarantee it.
OEM mounting hardware is reused. Factory pedal pad can be reused or we have a wide Variety of VM pads available.
Optional Pedal Pad:
- P2 underside mount drops pad 10mm from standard pad
- P3 stepped pad offers 2 different heights for sitting and standing
790 Stabilizer Sub mount and Bar Risers
A simple robust solution for the KTM 790/890 and Husqvarna 901** that provides an increase in handlebar height (1.0" rise) and the ability to install an under bar mounted Scott's Performance steering stabilizer.....or just use the riser portion for better ergonomics!
Features:
- Now shipping with upgraded tower/pin design. See far right images.
- 1.0" Handlebar Rise (25.4mm) for better control and less cramped ergonomics
- Retains the two forward factory offset positions for adjustability (can reverse perches for a total of 4 different offsets)
- Factory KTM Hardware Included for Mounting
- Lifetime Guarantee* (see warranty page for details)
Fitment
- KTM 790/890 Adventure S, R, & Rally Models - All Years
- Husqvarna 901** - All Years
Important Notes:
If you have your own Scott's Damper you can use either the +10mm stepped link arm or the +8mm stepped link arm to work with this kit. If you do not have one of these please select the appropriate option below to include a link arm and puller tool.
If you order this kit with a Scott's stabilizer everything necessary is included.
It is advised to remove the factory stabilizer when installing the Scott's Damper.